San Bernardino, CA 92401 to 92411 · San Bernardino County

Slab Leak Detection in San Bernardino, CA

San Bernardino sits at the foot of the San Bernardino Mountains, and most of its homes were built on concrete slabs decades ago. That age changes where a hidden leak starts and how it gets found. Here is how to tell a hidden leak from a sprinkler line or a tired water heater before anyone opens a floor.

7 ZIPs92401 to 92411 served
748 galIn 1 billing unit (100 cu ft)
1971Typical home build year (estimate)
15 minFor the 4 step meter test

Home›San Bernardino, CA

Short answer

In San Bernardino a slab leak is confirmed at the water meter before any concrete is touched. Shut off every fixture and the irrigation, then watch the low flow dial: if it keeps moving with the house shut down, water is escaping on your side of the meter, and a warm patch on the floor points to the hot line running under the slab.

  • The meter test takes about 15 minutes and 4 steps, and it separates the yard, the water heater and the slab
  • One billing unit is 100 cubic feet, which equals 748 gallons
  • One public housing estimate puts the typical San Bernardino home at a 1971 build, so a lot of original pipe is about 55 years old
  • Your own water bill names your provider and its billing period, and a hidden leak can run for a full period before the bill shows it
  • Permits go through the City of San Bernardino Building and Safety Division at 201 North E Street, 3rd Floor, San Bernardino, CA 92401
  • The city says most plumbing work needs a permit, with a few minor exceptions, and replacing pipe is permitted work
San Bernardino, CA · ZIPs 92401 to 92411

San Bernardino, California spreads across 7 residential ZIP codes in the Inland Empire, from the downtown core to Del Rosa, Verdemont and Muscoy. The build era of a home is the most useful clue when something starts leaking.

Why are hidden leaks common in San Bernardino homes?

Most homes across Southern California sit on a concrete slab with the water supply lines running in or under it. When a copper line under the slab develops a pinhole, water rarely shows up on the surface. You get clues instead, such as a warm floor, a meter that will not settle or a bill that climbs. One public housing estimate puts the typical San Bernardino home at a 1971 build, and ZIP 92401 shows the same median year, which would make a lot of original supply pipe about 55 years old now.

Age is only part of it. Local water is commonly described as hard, and minerals plus decades of flow wear copper from the inside. Ground movement around a slab adds stress to rigid pipe cast into it. None of these causes leaves a visible mark early, so a leak can run for weeks before anything on the surface changes.

Older slab homes

Homes from the 1950s through the 1970s are common in the older neighborhoods. Original supply lines have had decades to wear, and many have been partly repiped, so the first job is working out what the home is actually plumbed with.

Newer tract homes

Tracts built from the 1980s onward usually have copper under the slab that is now 30 to 40 years old, which is the range where pinhole failures start to appear in many homes.

Home builtTypical supply pipeWhat to watch
Before 1960Galvanized steel, often partly replacedRust, low pressure and mixed materials after past repairs
1960 to 1980Copper under the slabPinholes after 50 or more years, plus the original water heater
1980 to 1995Copper, and in some homes polybutylenePolybutylene is known to fail, so confirm the material first
1995 and laterCopper, later PEXFittings and water heater connections before the pipe itself

These eras are general. Your own home may have been repiped or remodeled, so the build year on your property record matters more than the neighborhood name.

What should I do first if I think there is a leak under the floor?

Start with what you can see and hear. Four signs account for most calls, and 2 or more together make a leak under the floor much more likely than a single one.

  • The water meter dial keeps moving with every fixture and the irrigation shut off
  • A warm or damp patch on the floor, often along a hallway or near a bathroom
  • The sound of water running at night when nothing is on
  • A water bill that jumps with no change in how many people live in the house

Then work through the order that costs the least: close the irrigation shutoff, check the water heater, and run the meter test in the next section. Those 3 checks usually narrow a whole house down to one system before anyone arrives.

Water on the floor right now? Close the main shutoff valve at the house first, then call (951) 484-2463. Do not wait for the next bill to decide.

How do I confirm it at the meter in San Bernardino?

This takes about 15 minutes and it is the most useful thing to do before any appointment. A water meter counts in cubic feet, and 100 cubic feet is 748 gallons, so a loss big enough to show on a bill is usually big enough to move the dial while you stand and watch it.

Shut everything off

Every tap, both toilets, the dishwasher, the washing machine, the ice maker and the irrigation controller. Nothing should be drawing water.

Read the low flow dial

Open the meter box and find the small triangle or star shaped indicator. It turns on any flow at all. Movement with the house shut down means water is leaving the system.

Isolate the yard

Close the irrigation shutoff only and watch again. If the dial stops, the loss is in the sprinklers. If it keeps turning, it is on the house side.

Separate hot from cold

Close the cold inlet valve on top of the water heater. If the dial slows noticeably, the hot line under the slab is the likely path.

Write down what the dial did at each of the 4 steps. Those notes are the first thing worth saying on the phone.

What happens during a leak detection visit?

A proper visit has 3 stages, and none of them involve cutting the floor. First the technician confirms your meter results and isolates the plumbing into sections. Second, each section is pressure tested to see which one loses pressure. Third, acoustic and thermal tools are used over the floor to pin the position down to a small area.

Only after the position is known does the conversation turn to repair. A spot repair, a reroute through the attic or walls, and a tunnel under the slab are the usual options, and the right one depends on how the pipe runs and what is above it. Our water leak detection and slab leak repair pages explain how that choice is made, and pipe rerouting covers the option that leaves the slab intact.

How do I choose a leak detection specialist in San Bernardino?

3 questions sort most providers quickly. Ask how they will locate the leak before they talk about repair. Ask what they will put in writing, including the scope and the price as a range, before any work starts. And ask what happens if concrete has to be opened and who restores the floor afterward.

Be careful with anyone who quotes a full repipe before the leak has been located. Also ask whether your slab is a post-tension slab, which some newer homes have, because cutting into one without knowing the cable layout is a real risk and the position of the leak has to be exact. You can check any contractor on the state contractor board lookup at cslb.ca.gov before you agree to any job of $500 or more.

Do I need a City of San Bernardino, CA permit to fix a leak under the slab?

The city says that with a few minor exceptions, building permits are required for plumbing work. Under the California Plumbing Code, stopping a leak without removing and replacing pipe is generally one of those exceptions. Where defective pipe has to be removed and replaced with new material, that counts as new work and a permit is needed, so a spot repair is usually exempt and a reroute or repipe is permitted work.

Permits for the city are handled by the Building and Safety Division of the Community and Economic Development Department, at 201 North E Street, 3rd Floor, San Bernardino, CA 92401, and the office line is (909) 384-5357. Exemption lists get revised, so confirm the current rule with the division before work starts, and ask your provider who pulls the permit.

What happens when you call?

The call works in 3 simple steps.

Make the call

Call (951) 484-2463 and tell them what the meter did, whether the floor has a warm patch and how old the water heater is.

Get connected

Your call is forwarded to an independent local service provider that covers San Bernardino. This website is not a service company and does not do the work itself.

Compare your options

Ask the provider how they locate the leak, what the written scope will be and what the price range looks like. You decide whether to go ahead.

Leak under a San Bernardino floor? Call (951) 484-2463 and be connected with a local provider.

Request a call from a local pro

Tell them what the low flow dial did with the house shut down, whether the floor has a warm patch, and how old the water heater is. That alone usually narrows it to one system. San Bernardino, CA 92401 to 92411.

Call (951) 484-2463

San Bernardino, CA leak detection questions

How can I tell if the leak is under the slab or out in the yard?

Shut off every fixture and the irrigation controller, then watch the low flow dial on the meter. If it keeps turning, close the irrigation shutoff only and watch again. If the dial stops, the loss is in the sprinklers. If it keeps turning, the loss is on the house side, and closing the cold inlet on the water heater tells you whether the hot line under the floor is the likely path.

Will my water bill show a hidden leak in time?

It can flag one, but late. A leak can run for a whole billing period before the bill reflects it, and your own bill shows the name of your water provider and how often it bills. One billing unit is 100 cubic feet, which equals 748 gallons, so even a modest leak adds up quickly. The meter dial shows the same problem in minutes, which is why it is the better early warning.

Can a slab leak be found without breaking the concrete?

Yes. Locating is done with meter isolation, pressure testing on isolated sections of pipe, and acoustic and thermal work over the floor. Concrete only comes into the picture after the position is established, and a reroute through the attic or walls can avoid opening the slab at all.

Should I check the water heater before calling about a leak?

Yes, it takes about 5 minutes. Look at the floor around the base of the tank and at the flex connectors on top. A tank that weeps at the base or a connector that seeps produces the same wet floor and the same restless meter as a leak under the slab.

Who does slab leak detection near me in San Bernardino?

This website connects homeowners with independent local service providers. When you call, your call is forwarded to a provider that serves San Bernardino, and you can ask them how they locate a leak, what they will put in writing, and what happens if concrete has to be opened.

My bill is high but the meter test looks clean. What next?

Check the usual suspects that do not always move the dial much: a toilet flapper that leaks slowly, an irrigation timer that runs longer than set, and a hose bib. If the bill still looks wrong, ask your water provider about a meter check and how its leak adjustment process works before you start repairs.

Areas we serve in San Bernardino, CA

Calls are taken for homes across 7 San Bernardino ZIP codes. Neighborhoods are listed by the ZIP they mostly fall in.

92401

Downtown, Carousel, Stadium West

92404

Del Rosa

92407

Verdemont, Muscoy, Arrowhead Farms, Wildwood Park

92410

Base Line

92405

North San Bernardino

92408 and 92411

West and southwest San Bernardino

This website connects homeowners with independent local service providers. We are not a service company and do not perform the work ourselves. Calls are forwarded to licensed professionals in your area.

Designed & developed by Rankvero.online